Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
pro2_transmitter [2018/09/26 16:08]
tedem
pro2_transmitter [2020/04/05 14:03] (current)
tedem [Notes and hints on assembling]
Line 14: Line 14:
 A detailed parts list can be downloaded from here: [[http://​www.meteocercal.info/​forum/​attachment.php?​aid=530|WeatherDuino Pro2 TX v3.12 - Parts List]]. A detailed parts list can be downloaded from here: [[http://​www.meteocercal.info/​forum/​attachment.php?​aid=530|WeatherDuino Pro2 TX v3.12 - Parts List]].
  
-Each WeatherDuino transmitter comprises a single printed circuit board (PCB) approximately 100mm x 60mm. The PCB has two main functions. First, it provides an interface to a number of sensors via connectors mounted around two sides of the board. Second, it provides a radio frequency (RF) link between an Arduino Nano microcontroller and a remote WeatherDuino receiver. Two RJ45 Ethernet-style sockets provide connections to a rain sensor and an anemometer. Many low-cost wind/rain sensors use these connectors ​so it is often possible to re-use redundant hardware.+Each WeatherDuino transmitter comprises a single printed circuit board (PCB) approximately 100mm x 60mm. The PCB has two main functions. First, it provides an interface to a number of sensors via connectors mounted around two sides of the board. Second, it provides a radio frequency (RF) link between an Arduino Nano microcontroller and a remote WeatherDuino receiver. Two RJ45 Ethernet-style sockets provide connections to a rain sensor and an anemometer. Many low-cost wind/rain sensors use these connectors ​but beware that not all use the same pin arrangement.
  
-**Insert image TxPCB.png here?**+{{:​wiki:​txpcb.png}}
  
-Apart from the rain gauge and anemometer, the PCB provides inputs for two analogue sensors (nominally solar radiation & UV), and three digital inputs (two I2C). It also has a 9 volt output which may be turned on and off by the WeatherDuino software. A typical use for this would be to control the fan in an aspirated radiation shield. The PCB has a space for a line driver IC which may be needed if the I2C sensors are not mounted close to the transmitter. It's a good idea to fit a DIL socket in this position so that the IC can be easily fitted later if needed.+Apart from the rain gauge and anemometer, the PCB provides inputs for two analogue sensors (nominally solar radiation & UV), and three digital inputs (two I<​sup>​2</​sup> ​ C). It also has a 9 volt output which may be turned on and off by the WeatherDuino software. A typical use for this would be to control the fan in an aspirated radiation shield. The PCB has a space for a line driver IC which may be needed if the I<​sup>​2</​sup> ​ C sensors are not mounted close to the transmitter. It's a good idea to fit a DIL socket in this position so that the IC can be easily fitted later if needed.
  
 RF communication is provided by a small daughter board located near the SMA aerial socket. Other major components on the PCB are a voltage regulator and a MosFET transistor which controls the external power feed. One very useful feature of the transmitter board is a temperature sensor. Although this is not as accurate as the off-board temperature sensor(s) it does provide an indication of conditions in the transmitter box. RF communication is provided by a small daughter board located near the SMA aerial socket. Other major components on the PCB are a voltage regulator and a MosFET transistor which controls the external power feed. One very useful feature of the transmitter board is a temperature sensor. Although this is not as accurate as the off-board temperature sensor(s) it does provide an indication of conditions in the transmitter box.
  
-**Document under construction… please come back later.** 
  
 ====== Where I can get the WeatherDuino Pro2 Transmitter?​ ====== ====== Where I can get the WeatherDuino Pro2 Transmitter?​ ======
Print/export
QR Code
QR Code pro2_transmitter (generated for current page)